Gunboards Forums banner

Status
Not open for further replies.
1 - 7 of 7 Posts

·
Super Moderator
Joined
·
3,867 Posts
Discussion Starter #1 (Edited)
DoubleD
Moderator


South Africa
1829 Posts
Posted - 08/22/2004 : 3:50:06 PM

For detailed instructions on assembly and disassembly of the Martini Henry rifle visit Jason Atkins website at http://www.martinihenry.com/DD

That isn't your Martini you have. It belonged to others before you and will belong to others after you are gone. Look after it an pass it on with pride. It deserves it....Malcolm Cobb The Martini-Henry Note-Book.
Edited by - DoubleD on 07/06/2005 11:54:49 AM

DoubleD
Moderator


South Africa
1829 Posts
Posted - 03/13/2005 : 1:15:05 PM

The following is provide courtesy of Mr. Graham Greene of W.W.Greener http://www.wwgreener.com and is for the Assembly and disassembly of Greener Martini's


quote: Dear Mr Dickens,




Attached are four separate sheets covering the instructions for the W W Greener GP Mk I. The GP Mk II differs slightly in that there are circlips retaining the pins instead of keeper screws and the associated parts are not quite the same since they accommodate these circlips instead of the keeper screws. If you would like the same sheets for the Mk II please let me know. The W W Greener Martini Action Police Guns were again very similar as were the many different W W Greener Martini Action rifles made for target practice, sporting purposes and the military. Some spare parts are available for the GP Mk II which was last made in 1998.

While my book (see attachment) does not provide instructions for disassembly or reassembly it does provide details about all the various models of Greener guns made including Martini action shotguns and rifles.

Best regards

Graham N. Greener

I have left these pictures larger than normal so you can read them.
To save them:
Right click on a picture.
From the drop down menu select copy.
Open a new document in Word, right click on the blank page and paste the picture.
Right click on the image and select format picture.
Click on the size tab and make the picture 8 inches wide.
Now you can print the instructions out.









DD

That isn't your Martini you have. It belonged to others before you and will belong to others after you are gone. Look after it an pass it on with pride. It deserves it....Malcolm Cobb The Martini-Henry Note-Book.
 

·
Super Moderator
Joined
·
3,867 Posts
Discussion Starter #2
Annual update
 

·
Copper Bullet member
Joined
·
2,455 Posts
Disassembly/Assembly of Martini Henrys & Greeners

Disassembly/Assembly Nepalese Gahendra MH


The very first thing to is take the cleaning rod out, put a piece of metal in the hole in the cleaning rod











Then turn the cleaning rod as you pull on it very gently

Some of the cleaning rod are to long to line up with the notch on forearm tip and you could push the cleaning rod stop into the receiver .
Cleaning rod stop looks like this











That why some of you can't **** yours, and I don't advise cocking them anyway until they are clean up you could brake something in the receiver


I sprayed everything down with WD-40 use want ever you prefer






Next

Take something sharp, I use a dental pick and clean out the screw slots






take the right size screw driver put it the slot , take small braes hammer and give a light smack then try to tighten the screw just a little then back it out




You may have to go back and forth, but it will come out






Next
Take a brass punch and punch out the pins



Drive it half way though then take a pair of vise grips and while twisting pull






After you get the 2 barrel bands off and the 3 pins out
Take the muzzle end of the forearm and gently pull down then push back up gently rocking the forearm until you can pull on the back of the forearm completely down and off




Then take the screw out of the fore arm tip


Take the tip off


You might as will take off the cleaning rod stop
 

·
Copper Bullet member
Joined
·
2,455 Posts
After that take off the stock screws and but plate


take rubber mallet and break the bond on the stock and receiver



if you can get it off good if you cant no problem

next is the receiver screws

Clean the heads of the screws up , there is one screw that is a retaining screw once you get it loose line the open end up to the lever screw and loosen the lever screw


once you get all the screws loose you can drive them out




Now wiggle the stock and the let the bottom fall out


And take the stock off

After all the screws are out every thing should come out of the receiver



The I put the small parts in a ultrasonic cleaner filled with diesel fuel , but can put your a pan of anything that will clean the parts up



Now clean your stock up I don’t care want you use to do this with, it’s your rifle
 

·
Copper Bullet member
Joined
·
2,455 Posts
Ok
Let’s put it back together


Put lever catch and the trigger on



Put trigger spring on




Put the hammer spring on





Do not put sling swivel on like I did



The next thing is the hammer extractor, and lever
They line up like this









Slip the hammer spring under the hand on the hammer







Pull the lever down



Insert the breach block



Now put the sling swivel on



Hope this helps, look for updates

NORM
 

·
Copper Bullet member
Joined
·
2,455 Posts
fixing broke Gahendra MH firing pin

The first thing I did was clean the hammer and grind down the face




Then I line both of the up in put them in a vise



After they lined up I put a pilot hole in it



Then I took a .124 drill bit and drilled half way though the head of the hammer





Then took the bit out reverse it, in the hole I just drilled




Then I chuck it up in my bench ,motor and taper it in the middle with a file




Then I heated up the drill bit with a torch and bent the drill bit to the angle of the other firing pin



I also silver solder it in place,

Then took it out the vise



Then trim it up







you may need to get a parts gun, from IMA
NORM
 

·
Copper Bullet member
Joined
·
2,455 Posts
Dixie gun works and order a tp0441 or a tp2300

there both the same spring








straighten spring, widen hole in spring then ether tap the spring hole to the thread of the screw or make lager than screw , put a nut on the bottom of the spring, if you didn't tap the spring put another nut on the top, you may have to grid some relief in the lower nut so the trigger return spring , now if you had to put a nut on top you will probably have inlet the stock for the nut




follow directions for spring steel





NORM
 
1 - 7 of 7 Posts
Status
Not open for further replies.
Top